Posts tagged ‘Magic Mesh’

New Video of Mesh Transfer Technique

For written steps on this technique see this post

March 25, 2009 at 1:31 pm 20 comments

Magic Mesh as “transfer film” for paper projects

Using transfer tape makes aligning the cut pieces of a vinyl image simple. (If you have no idea what I am talking about you may want to watch the video on this page.) It would be wonderful to use the same technique for paper-based projects, but the trouble is that commercial transfer tape, Cont-Tact paper or painters tape tear up the surface of your cardstock cutouts when it is removed.

In my quest for a solution, I tried Press-n-Seal first. I love Press-n-Seal, it has literally saved my son’s skin during cancer treatments, but it was not the solution to this problem. Like tape, it didn’t want to let go of the cardstock without a (destructive) fight.

In poking around my boxes of never-used supplies looking for sticky things, I found some Magic Mesh, and it fit the bill perfectly. (If you don’t know what Magic Mesh is click here.) You can also use the much cheaper and easier to find self-adhesive mesh drywall tape from a hardware store. Follow the steps below to use Magic Mesh/drywall tape to easily transfer your cutouts from mat to page:

1. Make your cuts, then remove the part of the cardstock you don’t want, while carefully keeping the parts you do want stuck down and in position on the mat (called weeding in the vinyl world). For cuts that are not clean, use an exacto knife to help you punch out the pieces and keep them in position.

2. Loosen the pieces from the mat a little, while keeping them in position. I do this by holding down one end with my finger or a toothpick and lifting the other end with the spatula tool. You only need to loosen one end of each piece to “break the bond” with the mat. The results will look something like the photo below. Notice how on each individual piece, one end is stuck in position and the other end is “free.”

mm1

3. Put a piece of Magic Mesh/drywall tape over the image adhesive side down and press down firmly over each piece of your cutout.

mm2

4. Remove the mesh from the mat and your pieces will come with it! Now would be a good time to do a trial positioning on your page or card. If something is a little off, the Magic Mesh/drywall tape is repositionable so it’s easy to scoot things around if you need to.

mm3

5. Turn over the mesh and apply your adhesive to the pieces of cardstock. Try not to get adhesive on the mesh.

mm4

6. Position the mesh with your glue-loaded pieces over your page and press into place.

7. Wait for the glue to dry and then remove the mesh, which can be reused. Or, if you are impatient like me, go ahead and remove the mesh before the glue dries, using the spatula if necessary to assist in the process. You could also try holding the pieces down with a toothpick through the open area of the mesh.

mm5

This is really a lot easier to do than to explain. You will get a feel for it pretty quickly and be able to adjust according to the stickiness of your mat and mesh, and the surface characteristics of your cardstock. This technique should be very helpful for paper piecing (without a Cricut, line up your handcut pieces over a printed guide, then transfer with Magic Mesh), for placing lettering (with or without a Cricut, use the grid on the Magic Mesh/drywall tape to line up individual letters), and especially for text in a circle or other complicated images that need to be positioned precisely. I’d love to hear how it’s working for you.

For a video of this technique see this post.

March 18, 2009 at 6:46 am 30 comments


Enter your email address to subscribe to this blog and receive notifications of new posts by email.

Join 3,466 other followers

Follow me on Twitter

Cricut and Sure Cuts A Lot Top 40
Silhouette Top 40
Sure Cuts A Lot Top 40
Make The Cut Top 40

Follow

Get every new post delivered to your Inbox.

Join 3,466 other followers